 |
|
       |
 |
|
The ECL-ACC960 proximity card reader is safe for outdoor and indoor use. It uses multiple LEDs and a beeper to indicate pass/fail card read status. It can be programmed to use card only, card or PIN, or card plus PIN combination for extra security. |
||||||||
 |
 |
WG support for anti-passback operation |
|
Audible beeper |
|
Metal case |
|
Weatherproof |
|
|
Bright LED indicators |
|
TTL serial output |
|
Built-in watchdog to prevent halting |
|
1024 users |
|
|
|
1200 event logs |
|
11 sets of time zones |
|
Time & attendance software support |
|||
|
The ECL-ACC970 proximity card reader is an advanced access control device in a zinc alloy weatherproof metal case that provides an LCD panel used for programming and to pass messages to the user. The design is weatherproof and vandal resistant which makes it suitable for outdoor applications. Built-in watchdog and anti-tamper functions. Easily integrated with other Eclipse access products. |
||||||||
 |
|
Big and clear LCD display, 4 lines text, 16 characters per line |
|
10-18cm card read range |
|
RS485 communication interface |
|
9600bps baud rate |
|
|
User defined time zones |
|
Holiday scheduling |
|
1024 users in network mode |
|
More than 65k users in standalone mode |
|
|
|
1200 event log |
|
Two programmable auto-open door zones |
|
Tamper resistant switch |
|
Alarm out function support |
|
|
|
TTL serial output |
|
Auxiliary WG port |
|
Adjustable door relay time |
|
Power: 10-24VDC |
|
 |
||||||||
|
The ECL-ACC980 (and ECL-ACC980IP) proximity card reader is an advanced access control device in a weather-proof case. It reads proximity cards and has an illuminated touchpanel to accept personal identification numbers (PINs). When a user presents a card, audio (beeper) and visual (bicolor red/green LED) feedback indicate the card is recognized (or not). For additional security, the touchpanel can be programmed to require PIN entry. It can operate in network or standalone mode. |
||||||||
 |
|
Illuminated touch panel key pad |
|
Card only, card or PIN, or card PLUS PIN |
|
LED and Beeper feedback |
|
Range: 10-18cm |
|
|
Anti pass-back support |
|
Holiday scheduling |
|
Tamper resistant |
|
1200 event logs |
|
|
|
1024 users |
|
11 time zones |
|
Requires 12VDC (power adapter not included) |
|
RS485 communication interface |
|
|
|
||||||||
|
This weatherproof proximity card reader is a perfect access control device for doors in factories, office buildings, and other sensitive areas. Maximum distance is approx. 18cm (7 inches), depending on weather conditions. Constructed of tough ABS plastic. Connects easily to our ECL-ACC1000 control panel. |
||||||||
|
|
|
Big and clear LCD display, 4 lines text, 1024 x 64 pixel graphic |
|
Unlimited site codes |
|
11 sets of time zones |
|
Up to 120 holiday schedules |
|
|
Auto-show work status (set via time zone edit) |
|
Master cards range assignable |
|
RS-485 support for networking (via controller or directly) |
|
Built-in door sensing and arming inputs (on/off) |
|
|
|
Auto open/close scheduling of doors |
|
Control mode, card capacity and card type assignable by user directly |
|
Built-in proximity reader and external Wiegand reader port |
|
Auto-discriminating between stand-alone & networking system |
|
|
|
Alarm function available (tamper, force entrance, door sense |
|
Networking: RS-485, 9600, N, 8, 1 |
|
External reader port: Suitable for all WG, ABA reader, 125K, 13.56M (Mifare) or 2.4G reader |
|
RF Frequency / Reading range 125 kHz / 10-18cm |
|
|
|
Door relay: 12VDC @ 2A NO/NC/COM 0.1-600 sec. latch type |
|
Alarm relay: 12VDC @ 2A NO/NC/(jumper) 0.0-600 sec. (COM Common) |
|
DI input: Egress button / door sensor / card sensor |
|
Transistor output: Arming / door sensor / card sensor |
|
|
|
Tamper switch limit switch (form C) |
|
Serial port: supported for AI-401R016, LED display, relay board, printer ETC. (4800, N, 8, 1) |
|
Dimensions: 127mm x 91mm x 46mm (5" x 3.58" x 1.81") |
|
Connect to PC using ECL-CN550 |
|
|
|
We've coupled a proximity card reader with a biometric fingerprint sensor to create a door/portal control device for facilities that require positive identity confirmation with controlled access. This proximity access card reader is coupled with a biometric fingerprint sensor for extra security. Maximum distance is approx. 15cm (5.9 inches). Constructed of tough ABS plastic. Connects easily to our ECL-ACC1000 control panel. Indoor use only. |
|||||||
|
|
Short response time |
|
Standalone mode, or use it in conjunction with a PC (software included) |
|
Large fingerprint capacity with high recognition rate |
|
Backup recognition mode for pool fingerprints, password or ID card |
|
|
|
Master card assignable |
|
10,000 users card capacity |
|
RS485 support for networking |
|
Fingerprint database download/upload support |
|
|
|
Built-in watchdog to prevent the system from halting |
|
External reader port 26/34 bit Wiegand format for anti-pass-back |
|
Alarm function available (tamper, force entrance, door open too long) |
|
Keypad locks for 30 seconds, while continuous error operation |
|
|
|
Universal serial port supported for LED display, printer, lift controller, ETC |
|
Lift control: 5,000/32 stops |
|
Access mode: card only, card or PIN, card and PIN |
|
Fingerprint access mode: card & fingerprint, card or PIN & fingerprint, card & PIN & fingerprint, 4 digit user number & fingerprint |
|
|
|
Matching mode: High end optical sensor 500 dpi resolution @ 8 bit gray scale |
|
Fingerprint capacity: 1450 |
|
Area of input: 18mm x 16mm |
|
Panel display: English, French, Italian, Danish, Greek, Spanish |
|
|
|
External reader port: suitable for all WG, ABA reader, 125K, 13.56M (Mifare) or 2.4G reader |
|
Networking: RS-485, 9600, N, 8, 1 |
|
Door relay: 12VDC @ 2A NO/NC/COM 0.1-600 sec. / latch type |
|
Alarm relay: 12VDC @ 2A NO/NC/jumper selectable 0.0-600 sec. |
|
|
|
Serial port: supported for ACC995, LED display, relay board, printer (4800, N, 8, 1) |
|
Anti-pass back |
|
255 door groups |
|
63 time zones |
|
|
|
11,000 event storage capacity |
|
Card reading range: 8-15cm (3.15"-5.91") |
|
Power: 9-24VDC, <5W |
|
Temperature: -20°C - 75°C (-4°F - 167°F) |
|
|
|
This proximity card reader is a perfect access control device for inside doors in any sensitive area. Maximum distance is approx. 15cm (5.9 inches). Constructed of tough ABS plastic. Connects easily to our ECL-ACC1000 control panel. |
|||||||
|
|
12 character numeric keypad |
|
1 red/green LED |
|
Internal buzzer for audio feedback |
|
11 sets of time codes |
|
|
|
120 holiday schedules |
|
Keypad will lock for 30 seconds after continuous error operation |
|
Built-in watchdog to prevent system halting |
|
Support delay relay auto-relock function |
|
|
|
RS-485 support for networking (via controller or directly) |
|
Built-in reader and additional reader support port for exit or anti-pass-back function |
|
Control mode, card capacity and card type assignable by user directly |
|
RF Frequency / Reading range 125 kHz / 10-18cm |
|
|
|
Networking: RS-485, 9600, N, 8, 1 |
|
External reader port: Suitable for all WG, ABA reader, 125K, 13.56M (Mifare) or 2.4G reader |
|
Door relay: 12VDC @ 2A NO/NC/COM 0.1-60 sec. latch type |
|
Alarm relay: transistor output/serial output (selective) |
|
|
|
DI input: Egress button / door sensor / card sensor |
|
Tamper switch |
|
Serial port: limit switch (form C) |
|
Dimensions: 112mm x 76mm x 25mm (4.41" x 2.99" x .98") |
|
|
|
Connect to PC using ECL-CN550. |
|||||||
|
|
This Wiegand proximity access card reader is easy to install and is perfect for outside. Maximum distance is approximately 8cm (3.5 inches). Constructed of tough ABS plastic. Operates in standalone mode or in a network with ACC900/ACC950/ACC995/ACC1000. |
|||||||
|
|
Wiegand proximity card reader |
|
Sealed design for outdoor use |
|
Low profile design |
|
One red/green LED |
|
|
|
Internal buzzer for audio feedback |
|
Network interface: WG 26/34, ABAII, ASYNC 9600, N, 8, 1 |
|
Available ports: tamper switch, Wiegand port |
|
1024 users with card and PIN combination |
|
|
|
65,536 users with card only |
|
Anti-pass back: multi-door when used with ACC1000 |
|
Remote operation supported when used with ACC1000 |
|
Wiegand port: 1 (WG26, WG34) |
|
|
|
Request to exit support |
|
Reader range 8cm (3.5 inches) |
|
DI inputs: egress button, door contact, arming switch |
|
Power: 9-18VDC variable auto detection, 1W |
|
|
|
Temperature/humidity: -10°C - 50°C (14°F - 122°F) @ 0-90% relative humidity non-condensing |
|
Dimensions: 80mm x 43mm x 15mm (3.15" x 1.69" x .59") |
|||||
|
|
This proximity access card reader is easy to install and is perfect for outside. Maximum distance is approx. 8cm (3.5 inches). Constructed of tough ABS plastic. Connects easily to our ECL-ACC1000 control panel. |
|||||||
|
|
Designer looks, sealed for outdoor use |
|
Anti-pass back: multi-door when used with ACC1000 |
|
Remote operation supported when used with ACC1000 |
|
Wiegand port: 1 (WG26, WG34) |
|
|
|
Request to exit supported |
|
Reader range 8cm (3.5 inches) |
|
DI inputs: egress button, door contact, arming switch |
|
Temperature/humidity: -10°C - 50°C (14°F - 122°F) @ 0-90% relative humidity non-condensing |
|
|
|
||||||||
|
|
This long range proximity access card reader is made of sturdy ABS plastic and can read a card from a distance of up to 60cm (23.6 inches) in optimum conditions. Connects easily to our ECL-ACC1000 control panel. |
|||||||
|
|
Range: 33cm-60cm (12.99" to 23.62") with the right tag |
|
Suitable for WG 26/34, ABA II, ASYNC 9600, N, 8, 1 |
|
Power: 9-18VDC, <4W |
|
Dimensions: 230mm x 230mm x 35mm (9.05" x 9.06" x 1.38") |
|
|
